Ed Livingston Sales Co., LLC

Rotary Drilling Equipment Broker

We Understand your drilling problems and equipment needs.

50+ Years DRILLING Industry EXPERIENCE  Including the Following:

Ed Livingston Sales Co, LLC-
2421 Rimrock Road
Billings, MT 59102
Tel. 307-587-5192~ Cell 307-899-5192
Email:ed@edlivingston.com

 

Featured Items DS

 

File Number Make  
1296-16 Versadrill V-100 2001 PRICE REDUCED FOR QUICK SALE: NOW $280,000
750/350 IR compressor--3x4 Mission Centrifugal mud pump--(7) pod 3 1/2" x 20' carousel--DTH oiler--Water injection system--7798 hours.
NCLUDED WITH RIG:
500' used 3 1/2" x 20' x 2 3/8 IF tool joit drull pipe.
(1) stabalzer
(1) DTH hammer drill
2002 IHC 2674 tandem axle chassis p/b ISM Cummins engine--205651 miles
425-5 GD/DSM 2500DD 2006 VERY HARD TO FIND GD-2500 DOUBLE DRUM.
70' x 120,000 max hook load capacity on 6 lines--10" GD retractable rotary table--Stacked Double Drum Drawworks (20,000 lb single line pull)--GD model GT-75 ton swivel--GD PAH triplex mud pump (350 gpm)--3x4 centrifugal charge pump
(3) axle Crane Carrier p/b C-13 Cat. Call  (307-587-5192)
for pictures & videos
1378-3 Gus Pech 1300 Brat 2003 This one owner which is still in regular service has been reduced to $99,000.00.
12" tube style mast--Two way cross top head slide--Planetary top head drive--GP-1300 hydrostatic tophead drive 0-65 RPM @ 13,000 ft lbs. 0-145 RPM @ 5828 ft. lbs. torque--24' stroke, cable, hydraulic cylinder actuated pulldown/retract drill system (pulldown 18,400 lbs/retract 24,500 lbs.--Pulldown/holdback feed control system--Two Speed retract--Dual hydraulic pump drive system with enlarged gear pumps for increased speed--Oil cooling system--Standard lighting (2)--Tower tool carrier for transportation--(4) hydraulic leveling jacks--Angle drilling lower tower supports--Hydraulic slide base--Hydraulic jib boom and extension-Hydraulic lowering tool guide with hydraulic tool clamp (enlarged to hadle 8 1/4" ID augers--2000 lb. (first layer) GP winch with large dameter drum, with headache ball, 1/4" x 150' cable--12,000 lb. (first layer) Pullmaster winch w/rapid reverse, 1/2" x 200' cable with swivel hook on jib boom--Diedrich sample hammer system--Stationary drill rod rack (10') with hammer holder for NWJ rods--Special 5' rod rack under 10' rod rack for 20 AWJ rods--Swing around auger racks (2) under both sides of rig--Swing around auger rack, rear mounted as per basic rig--2 1/2" U-joint attachment with 2" adapter--(2) sets auger guide bushing (8 1/4" ID)--Cotta heavy duty transfer case system.
18,200 hours--New engine at 12,900 hours (5300 hours on engine.
Rig is mounte on and powered by 2003 Sterling w/Cat engine
1409-2
Portadrill 524-3A 1979 REDUCED TO $70,000. WIDOW NEEDS TO GET THIS RIG SOLD!

1979 Portadrill model 524-3A mud & air rotary drilling machine complete with the following attached
equipment: LeRoi model 256S2 air compressor (500 cfm @250 psi) 42' mast—7 1/2" mechanically
powered through a 4 speed transmission, retractable rotary table—Hydrastically powered through 4
speed Funk transmission three drum drawwworks—(3) hydraulic leveling jacks Side pipe rack for
20' drill pipe—hydraulic powered (3) cylinder Bean water injection system -3 1/2" x 24' fluted kelly
and drive bushing—Breakout wrench and drill pipe slips & Misc. bit subs.
INCLUDED WITH RIG.
Included with rig is 22 joints (440’) used 3” x 20’ x 2 3/8IF tool joint drill pipe slotted for breakout.
Rig is mounted on and powered by a 1979 Kenworth model C-500 tandem axle chassis.P/B Detroit diesel engine.