Rigseller1  Ed Livingston Sales Co.

drilling rigS

e Number Make Model Year Equipped Carrier Click on Image to Enlarge
1217-1 Ardco Buggy   ALL TERRAIN CARRIER

6 x 6 Ardco articulated steering all terrain buggy p/b 453 Detroit and New Process model 542 (5) speed transmission--17' 6" bed length--Live PTO on transfer case--700 Ramsey wiinch on front of rig--Lock in/out on front axle--New 10 ply Terra tires.
Newly rebuilt 453 engine--New hydraulic hoses--New tires--Cleaned & Painted
 
1241-2 BE 22-W   Series II p/b QX Series 6 cyl. Hercules engine--Auto braces--Main line has approx. 300' 3/4" cable--Sandline has approx. 500' 3/8" line--Casing line has 5/8" line and (2) part (1) sheave traveling block--No cat head.
INCLUDED WITH RIG:
(1) set of tools (your size choice) to include:
(1) stem
(1) set jars
1988 Ford single axle chassis w/gas/propane engine & 5 x 2 transmission.
1251-1 BE 22W 1958 Standard 22-W--Allis Chalmers diesel deck engine--500' 3/4" drill line--5/16 sandline--SN 119234
(1) String of tools included with rig. (call for options)
Rebuilt jackshaft--New bearings, clutch pads, brake bands, sand line friction have little use since replacement.
1962 IHC R-190 w/406 gas engine and 5 x 4 transmissions. Air brakes--
1241-3 BE 27-T   This model BE is larger than a 60-L but does not spool much cable as they were for blast holes--300 CID 6 cyl. Ford Industrial deck engine--Very good cables (only 4 years old)--300' Main line--300' 3/8 sand line.
INCLUDED WITH RIG:
(1) set of tools (your size choice) to include:
(1) stem
(1) set jars
Old truck that does not run.
1241-1 BE 36-L   VERY NICE Standard 36-L w/ 54' mast--Sandline drum--(2) catheads
INCLUDED WITH RIG:
(1) set of tools (your size choice) to include:
(1) stem
(1) set jars
(1) bit
MANY OTHER TOOLS AVAILABLE AT ADDITIONAL COST
Tandem axle trailer
957-9 BE 28-L   Standard 28-L--54' telescoping mast with guy lines--(3) reels with lines on each reel. (exact amount of line of each reel unknown)--Casing reel has (3) sheave traveling block--Lister? Air cooled diesel engine--Catheads Trailer Mounted
957-6 BE 36-L   STANDARD 36L WATER WELL RIG COMPLETE WITH DIESEL ENGINE AND 54' MAST.
BITS & TOOLING ARE AVAILABLE AT EXTRA COST (CALL FOR DETAILS AND PRICING)BE 36-L
Trailer Mounted
1125-7 Challenger 320 1980 REDUCED PRICE ON THIS COMPLETE READY TO DRILL PACKAGE!
1980 Challenger 320 complete with 64/150 one piece mast w/stabbing board--60 Series Detroit diesel (430 hp) and LBT-5860 Allison automatic transmission--Stacked double drum drawworks w/air clutches--Paramac 12" Hydromatic brake--(6) part 7/8" lines both drums--(2) Mckissick 75 ton traveling blocks--Oilwell 17 1/2" rotary table--Howard-Turner 100 ton swivel--4 1/4 x 37' hex kelly--Varco roller type drive bushing--Make up and break out catheads--Hydraulic leveling jacks--
ACCESSORY EQUIPMENT INCLUDED WITH RIG.
MUD PUMP: Wilson 600 7 1/2 x 14" duplex mud pump--Gear end SN:600389A with high pressure forged steel fluid end and screw caps--Fluid end SN: 45273--Fitted w/6" liners and pistons--p/b electronic 60 series Detroit diesel--Model: 6067PK60 (500 HP)-- on oilfiled skid w/ roof, mud guage, shear relief valve-- and air contr--Weight approx. 70,000 lbs--11' 8" W x 27' 2" L x 10' 2" H..
TUBULARS: Approx. 3600' used 4" x Range II bottleneck x 3 1/2 XH tool joints
(10) 5 1/2" x 30' smooth w/ 4" H-90 tool joints drill collars.
GENERATOR: 200 KW Generator p/b NT855 Cummins
SUBSTRUCTURES:
(1) 6' substructure
(1) 11' substructure w/V door and cat walk
MUD TANKS:(1) 190 bbl (3) compartment mud tank w/single screen shaker(8' W x 4 1/2' H x 30' L)
(1) 200 bbl. (8'W x 4 1/2' H x 35'L) (3) compartment auxiliary tank
BOP EQUIPMENT: Regan 10" x 3000 psi annular.
Hydril 17K80 Closing Unit w/2 80 gallon units.
ROLLING STOCK:
1979 Aztec Pipe Trailer
1978 Columbia Pipe Trailer
1995 6 x 6 Oshkosh (4) rear axle heavy duty chassis p/b L-10 Cummins and Allison automatic Transmission complete w/90 bbl tank--Sunstrand hydrastatic pump and motor powered 3" Gorman Rupp pump.
1995 Freightliner Dog House.
MISC. ITEMS: Rauch hyd. pipe spinner 3 1/2 to 7"--Tongs--Tools--Pipe handling equipment--(2) pipe tubs plus plus
(5) axle carrier
1230-1 CME 75 1981 3L6 Moyno Pump--Ford 300 CID gasoline industrial deck engine--(3) hydraulic leveling jacks--Sandline drum--(1) hydraulic winch--Automatic hammer--No cathead. 1982 IHC 4700 single axle chassis p/b DT-466 diesel engine
1230-6 CME 850
Track
1984 Rubber Track Mounted CME-850--15,000 ft. lbs torque-3L6 Moyno Pump--Safety Hammer--Cathead---(2) rear hydraulic leveling jacks--INCLUDED WITH RIG:
75' 4 1/4" HS augers and sample rods.
Crawler Mounted w/ low ground pressure rubber tracks w/gasoline engine.
1189-1 CP T-650 Retro 1972 RETROFITTED WITH 500/350 SULLAIR
twin screw compressor--3406B Cat deck engine--Sandline drum--(3) hydraulic leveling jacks--Side pipe rack--Water injection--DTH oiler
AVAILABLE AT EXTRA COST:
WATER TRUCK: 1975 Ford LN-9000 6 x 6 w/270 Cummins diesel--15 speed transmission--1600 gal flat bed water tank--40,000 lb. front winch--
AUXILLARY AIR COMPRESSOR PACKAGE:
CP model PB-83 piston compressor 450cfm @ 250psi--p/bD-333 Cat diesel--fuel tank--Air tank--skidded.
1972 Ford LN-8000 with 1160 Cat desel and 5 x 3 transmissions.
1089-1 CP 650-WS 1978? PRICED TO SELL!  CALL NOW!

800/300 GHH compressor--3406 Cat deck engine--4 1/2 x 20' carousel--side pipe rack--(3) hyd. leveling jacks--Sampling cyclone.

Ford 8000 tandem axle chassis with 3406 Cat diesel engine
1171 CP T-650 1978 GREAT BUY ON A GOOD STARTER RIG
CALL NOW!

500/250 CP piston air compressor New in 1984--671T Detroit diesel deck engine--4 1/2' x 25' carousel-Bean water injection--DTH oiler--(3) hyd. Leveling jacks--
1976 Ford 9000 tandem axle chassi with 350 Cummins diesel engine.
920-4 Driltech D-40K SAM 1981/2012 TOTAL REFABRICATION!
SLIDING ANGLE MAST
60,000 pullback--New 900/350 twin screw air compressor--New 600 hp series 60 Detroit deck engine--New Bean LO918 triplex injection pump--DTH oiler--Lang special designed tophead drive.
INCLUDED WITH RIG:
Approx. 2000' good used 4 1/2" Matrix dual tube pipe.
Misc. DTH hammers & tooling
Cyclone and rotary splitters included but not mounted.
REPAIRS & UPGRADES:
This rig has had very extensive updates, major and minor repairs to include the following: New deck engine with new radiator/innercooler unit--New elgi 900/350 screw compressor, new Sullair Compressor cooler, New Sullair compact receiver tank, separate cooling systems for engine and compressor, all new air controls regulators and air inlet system--All new filtration (compressor and engine use same filters)--All new leaf type chains for pulldown and pullback (3 to 1 safety factor)--All new hydraulic hoses, valves and rebuilt pumps--New Bean triplex injection pump--
1981 tandem axle Crane Carrier chassis completely gone through including new wiring, new air system (tanks and lines & dryer), new glass, new tires.
1162-1 Driltech D-25KW 1998 900/350 Sullair--3406E Cat deck engine--8900 hours--(6) pod 4 1/2 x 20' carousel--DTH oiler--20 gpm Bean water injection--Foam injection--washing wand.
INCLUDED WITH RIG:
680' used 4 1/2 x 20' drill pipe--(2) used 6" hammers--(1) Petol wrench.
1998 Ford 3126 tandem axle chassis with Eaton/Fuller transmission and wheel and axle locks.
1130-1 Driltech M5 Marlin 2006 LESS THAN 1000 HR

1050/350 air--I-Beam style mast--Single stem loader--Water injection system--DTH oiler- Side pipe rack and fast slide--Included with rig:
300' 4 1/2 x 20' drill pipe--(2) DTH hammers--T150 Super Jaws under reamer--Diverter

 
1149-1 Ewbank M-51 1982 PRICE REDUCED

CHECK OUT! NICE 2000 CLASS DOUBLE DRUM

40' x 75,000 lb gross capacity mast--(3) drum drawworks w/Twin Disc air clutches (rated hook load capacity 60,000 lbs on (4) lines)--(4) part 5/8" lines both main drums--Single brake bands on main drum are 4" x 22"--Deck engine is a 3-53 Detroit diesel engine (very economical)--12 1/2" opening Howard-Turner rotary table w/31" opening when retracted--Table is powered by a drop box through 4 speed Allison Automatic Trans--(6) hydraulic leveling jacks--4 1/4" x 23' square kelly--(1) hydraulic breakout/makeup cylinder--3" Ewbank swivel--3" standpipe, rotary hose and mud lines--(1) hydraulic cathead--Totco dual weight indicator--AVAILABLE AT EXTRA COST: (Call for pricing)

MUD PUMP: Gaso 1550-C 5 x 10 Duplex mud pump p/b 471 Detroit diesel through Allison Trans--(drilled 1 well 2166" since complete rebuild of fluid end and engine)--1000 psi pressure guage--Shear relief valve

DRILL PIPE:
500' good used 3 1/2 x 20' x 3 1/2 IF tool joint drill pipe--

1600' NEAR NEW (drilled 1 well) 3 1/2' x 20' x 3 1/2 IF tool joint drill pipe--

DRILL COLLARS: (10) 4 3/4" x 20' x 3 1/2" XH drill collars w/slip recesses (Only drilled 1 well since shortened and rethreaded--

DOGHOUSE:7' x 10' Trailer mounted doghouse w/benches and knowledge box--

DRILL PIPE TRAILER: Used tandem axle oilfield float w/rolling tailboard--

TRACTOR:1978 White "Konstructor" tandem axle tractor p/b 671 Detroit w/5th wheel to pull rig--

TANKS:
210 bbl. Skidded water tank
500 gal. diesel tank.

MISC. TOOLING:
All necessary subs and changeovers.
All handling tools either new or remanded prior to last well.
(2) Drill string floats.
(1) set BVM type LF rotary tongs w/heads.
(1) Varco SDS 3 1/2" drill pipe slips w/flex handles
(1) Den-Con drill collar slips w/flex handles.
(1)unused Den-Con 3 1/2" drill pipe elevators.
(2) 3 1/2 IF hoist plugs w/swivel.
(2) 3 1/2 XH hoist plugs.
(2) 9 7/8" bits and breakers.
(4) 6 1/4" oilfield quality bits and breakers.

Rig is stated by owner to be in excellent, ready to drill condition. It has only drilled 1 well since being set up and last drilled summer 2008 to 2166' total depth. Moves and rigs up very fast. Very economical and fuel efficient. A nice rig for large diameter water wells or shallow production drilling. Owner prefers to sell as a package but will consider selling rig separate but will not sell any accessory items until rig is sold. There is a discounted package price.

Trailer Mounted
1133-1 Ewbank/EDSI M-100 2000 980 TOTAL HOURS!! REVERSE/CONVENTIONAL  PRICE REDUCED!!

MAST: 65' x 125,000 gross capacity one piece rectangular and square tubing mast--Casing clearance 26" up to 46' long or 32" to 36' long, crown has ample sheaves for two (3) sheave blocks plus sandline sheave--Stabbing board--6" stand pipe w/3" "Y" connection to allow the hook up of an auxillary stand alone mud pump for conventional mud circulation drilling.
DRAWWORKS: (3) drum design p/b two-speed range hydrostatic drive--Both kelly and hoist lines have 20,000 lb. single line capacity. 100,000 lb. limited hookload capacity on 6 lines--Both drums have 6" x 24" brake bands--Sandline drum for up to 3000' 1/2" cable--Has 6" x 24" single brake band.
POWER SUPPLY: (2) Cummins model 6CTA8.3P turbo charge engines. 260 hp each. Each engine can power all rig components, powered through (2) six-strand diamond chain, oilbath compound case.
LDL HOLDBACK SYSTEM:
(2) 20,000 lb. SLP hydraulic cylinders are installed on the back side of mast. (1) each for the kelly and trip block--Each have automatic mast overload protection, weight indicator, and micro feed on drill string/casing load for precise feed off/holdback control
ROTARY TABLE: Ewbank superior design 18" opening which can be tilted up to allow up to 36" clearance p/b two-speed range hydrastatic drive--up to 20,000 ft. lbs torque
KELLY & SWIVEL: 6" ID reverse circulation swivel w/center airline connection--6" ID x 30' kelly and drive bushing-- 6" kelly hose.
TONG POWER: (2) hydraulic cylinders are installed on the back of the mast to provide power for the tongs w/controls at drillers station.
CENTRIFUGAL PUMP:
6 x 6 MCM hydrostatic powered--Up to 1800 gpm @ 95 psi capacity w/air primer.
AIR COMPRESSOR: Sullair (2) stage 750 cfm @ 350 psi air compressor powered from compound case.
DUPLEX PUMP: Failing model FM-45 5" x 6 1/4" hydrastatic powered.
VENTURI MANIFOLD: For reverse circulation drilling.
AUXILLARY WINCH:
5000 lb. capacity mast mounted
LEVELING JACKS: (4) 5" x 30" hydraulic and (2) rear mounted telescopic type screw jacks.
MAST LIGHTS: 110 volt fluorescent lights in mast, control panel and components.
980 TOTAL HOURS!

 

Twin "I" Beam gooseneck three axle (w/4th tag axle) trailer--(2) fold down catwalks on each side including hand rails and steps--Road travel width is 11'
1081-2 EZ-Bore 100-42 1980 100' Quad kelly--4-53 Detroit deck engine--Allison automatic transmission--42" ring gear--Hydraulic pull down--Hydraulic push out--(3) hydraulic swing arm cylinders--(2) rear hydraulic outrigger jacks--(1) hydraulic front jack--
*Note: the bucket shown in the picture is not included with the rig.
1980 Mack RD68657600 tandem axle chassis p/b Mack diesel engine and Maxi-torque 5 speed hi-lo transmission.
1260-1 Failing 1250 1978 GREAT PRICE INCLUDING LOTS OF EXTRAS!
Rebuilt Failing model FM-45 5 x 6 1/4" duplex mud pump--Development air compressor--5 1/4" retractable rotary table--(2) part lines both drums--Sandline drum--2" swivel--3 3/8" x 23' fluted kelly & drive bushing--Breakout tong--(3) hydraulic leveling jacks--Side pipe rack for 20' drill pipe w/fast slide--Chem Grout Gas/hydraulic powered grouter mounted behind cab--
COMPLETE RIG PACKAGE INCLUDES THE FOLLOWING:
(20) pieces (400') 3 1/2 x 20' x 2 3/8IF flush joint drill pipe.
(6) pieces (90') 3 1/2 x 15' x 2 3/8IF flush joint drill pipe.
(3) stabalizers
(2) extra kellys
(1) portable mud pit with (1) cone desander unit.
Approx. 30 used bits.
Misc. bit subs, pipe handling tools & other items too numerous to mention
1978 GMC tandem axle chassis p/b 6V53 Detroit diesel and 10 speed RR Transmission.
819-27 Failing CFD-1B   5 x 61/4 Failing mud pump--Hydraulic Pulldowns--5 1/4" non retract table--3 3/8 x 23' fluted kelly--(2) rear hydraulic leveling jacks--swinging breakout tong--Side pipe rack--Bailing drum--
New kelly, bushing and hydraulic leveling jacks.
6 x 6 Kaiser-Jeep 5 ton cargo truck-Front Winch--Refabricated by Memphis Equipment Co. 1998.
1223-1 Failing 1500-SS   HEAVY DUTY MUD/AIR PRICED TO SELL!
600/125 Air (LeRoi 100S2 compressor)--5 x 6 1/4" (Failing FM-45) mud pump--40' mastw/stabbing board--3 1/2" x 23' kelly--Automatic kelly chuck--(2) part lines both drums--Bailing drum--GD air operated water injection pump--Breakout table--(2) rear hydraulic leveling jacks--
Ford F-800 tandem axle chassis with 534 gasoline engine and 5 x 2 transmissions.
819-24 Failing 1500-SS   4 x 5 GD mud pump--Ford 300 CID Industrial deck engine--Automatic chuck--2 3/8" x 26' fluted kelly--Sandline drum--36' mast (with longer crown section exchanged)--Breakout table--Cathead-- 1991 IHC 4700 single axle chassis w/DT-466 IHC diesel.
(Add $5000 for the truck)
1198-1 Failing CF-15 1973 5 X 6 1/4 Failing mud pump--Davey 3 cylinder air cooled air compressor--Mechanical clutches on drawworks-27' mast--2 7/8 x 23' kelly--2" swivel--Side pipe rack w/fast slide--5 1/4" retractable rotay table--Hydraulic pulldowns--BJ breakout tong--yers water injection pump--No bailing drum--Operators and helpers platforms. 1973 Ford tandem axle w/3rd tag axle chassis. 8V71 Detroit diesel engine. Odometer shows 21, 572 miles.
1219-1 Failing CF-2000 1973 A VERY NICE 2000 PACKAGE
58' mast w/stabbing board--Double Drim drawworks w/air clutches & double brake bands both drums--(6) part lines both drums--Spinning cathead--No bailing drum--18" Failing flip up rotary table--No pulldowns--(4) hydraulic and (2) manual leveling jacks--5 x 10 GD duplex mud pump on deck--Weight indicator--(2) hanging balanced tongs--Working platform--Elevator links.
INCLUDED WITH RIG:
DRILL PIPE: Approx. 1700' 3 1/2" x Range II x 3 1/2IF slotted for breakout tool joints--Tubescoped White Band
DRILL COLLARS: (11) 6" x Range II drill collars.
PIPE TRAILER: Gooseneck type with cat walk
(1) 3 1/2" BJ 100 ton elevators
(1) 3 1/2" pipe slips
Misc. handling tools
1973 KW tandem axle chassis p/b 350 (big cam) Cummins.
1265-1 Failing CF-2500   DOUBLE DRUM 2500
58' mast w/stabbing board and swivel guide rails--Stacked double drum drawworks w/air clutches--Parkersburg 15" double hydromatic brake--Pulldowns (chains available but need to be reinstalled)--Series 60 (475 HP) Detroit diesel deck engine--18" Howard-Turner rotary table--(2) 3 sheave McKissick traveling blocks- (6) part lines both drums--4 1/2" x 40' kelly--Roller type kelly bushing--3" ID x 40 ton swivel--3" kelly hose--(5) hydraulic leveling jacks--Weight indicators both drums--(2) tongs--Platforms, walkways, railings and stairs.
Tandem Axle Trailer
1064-2 Failing 2500-A   58' mast w/stabbing board--Single drum drawworks with sandline drum--air clutches--Cathead--Hydraulic and manual leveling jacks--(2) 471 Detroit diesel engines--GD FY-FXX 7 1/2 x 8 mud pump--(4) part 7/8" drill line--Failing 3" swivel--4 1/4 x 38' square kelly w/roller type bushing--18" Failing rotary table--(2) makeup/breakout tongs--Hydraulic breakout cylinder--(1) set 3 1/2" center latch elevators--(1) set drill pipe slips. Trailer Mounted
1033-2 Failing 2500-A   FAILING 2500-A complete with the following attached equipment:
65' x 133,000 gross capacity one piece mast--stabbing board--Single drum drawworks w/Aeroflex 16" air clutch on main drum p/b (2) 471 Detroit diesel deck engines w/manual transmission--Sandline
drum--18" Failing rotary table-swivel--Cat head--4" x 34' square kelly w/solid kelly bushing--(1 )front hydraulic leveling jack--(6) screw type leveling jacks--(2) makeup/brakeout tongs-- 5 x 10” duplex mud pump
Trailer Mounted
1268-1 Formost DR-24 2008 3000 total hours--Foremost Model DR 12/26P-60/24-900--IR 1070/350 Air--Tophead model RC110 (9600 ft/lbs torque) w/two speed operations & torque control--24" standard lower drive--10" discharge swivel w/6" & 8" casing adapters--8" & 10" casing jaws w/6" adapter from 10" jaws--Single rod loader--Service winch (4500 lbs capacity) w/remote control--Rotating and telecoping jib boom--Sandline assembly w/disc brake (8500 lbs capacity)--Cyclone c/w height adjustment--5" x 50' discharge hose assy--Side pipe rack--Breakout and holdback wrenches for 4 1/2" pipe--12 volt lighting system--DTH oiler--Myers 20 gpm water injection system--Approx.3000 total hours-- 2009 Kenworth Model T-800 Tier 3 chassis p/b Cummins ISX (550 hp) diesel--Upgraded cooling--Jake Brake, AC, & Stereo--26,000 lb front and 46,000 rear axles.
1277-1 Frac Truck 75 GPM 1997 Inflatable Baski packer 50% worn. Frac pump 60gpm driven by a Ford 258 motor. 300' of heavy wall frac pipe. 75gpm water pump. All wrenches and clamps. New PTO, hydraulic pump, 19'6" boom with pull master winch. 280 foot 3/4hp 10gpm test pump on reel. 500' reel to pull pumps. 1997 GMC C-6500 single axle flat bed truck, 6.0L gas engine, Automatic transmission, 145,000 miles, New Tires.
1272-1 GD 500 1976 5 x 6 GD mud pump--5 1/4" retractable table--Hydraulic pulldowns(presently inoperable but can be repaired w/ some new parts. Price has been discounted $5000 for repairs)---30' mast--2 7/8 x 23' fluted kell--2" swivel--Mud guage--Shear relief valve--(2) rear hydraulic leveling jacks-- 1998 IHC model 4700 single axle chassis p/b IHC DT-466 diesel engine and 6 speed transmission.
954 GD 500 1977 4 1/2 x 5 GD mud pump--290 cfm @ 50 psi air compressor--25' mast--3 1/2" x 15' fluted kelly--5" non retract table--Side pipe rack for 10' pipe--Operators/helpers platforms--No hyd leveling jacks-- 1977 Ford F-600 4 x 4 single axle chassis with 361 gas V/8 engine--Front winch
1262-1 GD 1000 1976 RETRACTABLE TABLE!
5 x 6 GD mud pump--5 1/4" RETRACTABLE rotary table--Hydraulic pulldowns--3 1/2 x 23' kelly--(4) hydraulic leveling jacks--20' side pipe rack w/fast slide--Operator and helper platforms--
1996 IHC 4700 single axle chassis with DT-466 diesel engine and Spicer 7 speed transmission.
1256-1 GD 2000 1976 EXTRA HEAVY DUTY 2000
(2) 6" x 10" GD duplex mud pumps w/11" (3) plate clutches--A separate gear boxes for each mud pump--Speedstar SS-25 double drum drawworks w/4" shaft and modified 18" air clutches--MAST: Reinforced to 90,000 lb. capacity x 58 W/ stabbing board--Water brake--
All Air clutches except mud pump--Pulldowns--(2) BJ Tongs--4 1/2" x 36' square kelly--McKissick (3) sheave traveling block on kelly & same on hoist line complete with spring loaded hook--10" retractable rotary table w/905 Fuller transmission--NEW 12 KW generator--Hydraulic powered Cat mist pump--(4) hydraulic leveling jacks--Walkways and hand rails--(2) 792 drop boxes--(6) strand transfer case--Chain case for drawworks and rotary table--Weight indicator both drums--Mud pressure gauge.
AVAILABLE ACCESSORIES
2000' good used 4 1/2" x 20' x 3 1/2IF drill pipe.
(5) 5 7/8 to 6" x 20' drill collars.
1978 Western Star pipe and tool truck
1994 Volvo pipe truck
Rig pipe handling tools
1976 Crane Carrier Corp (4) axle chassis p/b N-14 (460 hp) Cummins and Fuller 147-8LL transmission.
739-10 GD 2000 1976 5 1/2 x 10 GD mud pump--58' mast w/stabbing board--10" retractable rotary table--4 1/2 x 24' hex kelly--(4) hyd. leveling jacks--Hydraulic pulldowns--(2) 3 sheave traveling blocks w/6 part lines--Hydraulic breakout cylinder--(1) spinning cathead--Bailing drum--(2) cylinder Bean water injection system--Operators and helpers platforms--Weight indicator

1976 (4) axle Crane Carrier Corp. chassis with near new N-14E electronic Cummins diesel engine and RR transmission.
906-1 GD 2500SD 1980 70'/110,000 one piece vertical free standing mast w/stabbing board Single Drum drawworks w/air clutches (80,000 lbs capacity on (6) lines--Sandline drum 13,300 lbs capacity--(1) 671 Detroit diesel engine--(1) 65 ton 3 sheave traveling block--6 part 3/4" lines--18" GD rotary table--Howard Turner swivel--(2) catheads--(2) breakout/makeup tongs--(4) hyd. Leveling jacks--6" x 40' hexagon kelly w/ bushing--3" standpipe and mud lines-- (3) axle trailer
1120-1 GD 3000   ABSOLUTELY GORGEOUS!
RIG REDUCED $1,000,000

MAST: 95' x 200,000 lb. hook load capacity Lee Engineering vertical freestandiing hydraulically raised and scoped w/stabbing board.

DRAWWORKS: Gardner-Denver 3000 single drum with sandline drum--121 Hydramatic brake--1" drill line--p/b (2) 671 Detroit diesel engines (175 hp each) thru compound case.

SUBSTRUCTURE: Low back model--Gardner-Denver 8'x8'x4' clearance under table work platform--Mud boat.

ROTATING EQUIPMENT: Howard Turner 1825R (18") rotary table--King 75WP swivel--4 1/2" x 40' square kelly w/roller type bushing.

TRAVELING EQUIPMENT: (1) Mud King 110 ton/(4) sheave traveling block--Elevator links--

TONGS: BJ Type LF--BJ Model CTS power casing tongs w/2 3/8", 2 7/8" & 4 1/2" jaws.

MUD PUMP: (1) Gardner-Denver FXN 7" x 14"( fitted w/5 1/2" liners)--Quick change valve caps p/b 60 Series Detroit 14L (425 hp)--Master skidded in steel house.

MUD SYSTEM: 225 bbl mud tank w/ 5 x 6 x 11 Mission Magnum mix pump, Derrick FLC 503 Flo Line shaker--No cones--p/b John Deere diesel engine--80 bbl Mud system w/5x6x11 mix pump p/b 471NA Detrot diesel Premix. 8'Wx7'Hx10'L w/12' covered porch.

GENERATOR:(1) Kohler Model 100REOZLC 88KW capcity p/b John Deere diesel engine.

ADDITIONAL EQUIPMENT: 200 bbl water tank,1300 gal fuel tank, Doghouse & change house all mounted on 42' tandem axle trailer.

MISC: A-1 7 degree survey tool--Toolpusher trailer--Pason Multi pen electronic recorder with satellite download.

TUBULARS: None included

BOP EQUIPMENT: None included

Tri-axle trailer
819-12 Geoprobe Truck   2000 LOGGING TRUCK WITH 3 PROBES!
Century Geophysical Corp. logging unit complete with truck engine PTO driven generator, enclosed van with 300 meter (120 VAC operation) electric winch with cable and swing out boom.

DENTIFICATION INFORMATION:
On the back of the primary logging system the plate reads:
Compuil - DG Model #5
DTV - 029 (the last number was difficult to read due to scratches, I am pretty sure it is a "9", could be a "3")

The plate on the back of the small control box states:
RDH PS - 033


PROBES INCLUDED:
Probe #1: model 9065 hole caliper logging tool--Used in measuring up to 20" diameter boreholes. SPECIFICATIONS: 54" L x 1.7" diameter x 17 lbs.--Temp. 140 degrees-- Pressure 4000 psi--logging speed 30' per minute.
Probe #2: 9041 Natural Gamma probe SPECIFICATIONS: 84" length, 2.5" diameter, 33 lbs, temp. 194 degrees, Pressure 3300 psi, logging speed 30 ft. per minute.
Probe #3 9060 Natural Gamma, SP, Resistivity logging probe.
Mounted on 1977 Chevrolet C-60 single axle truck w/gasoline engine. Odometer shows: 85498 miles.
1199-1 Geo-800   1987 GREAT GEOTHERMAL HEAT LOOP RIG!
Tophead drive--3 x 4 centrifugal pump--(3) hydraulic leveling jacks--Deck mounted grouter with Bowie pump--Side pipe rack--Hydaulic pull downs--Pick up line. Operators and helpers platforms.

AVAIABLE AT EXTRA COST:
2 3/8 drillpipe.
Portabel mud pit
1987 Ford 700 tandem axle chassis with 6.6 liter diesel.
1219-2 Gus Pech H-48 1985 ALL HYDRAULIC BUCKET RIG
Super George--100' Quad kelly--48" ring gear--All Hydraulic driven--3408 Cat deck engine--(3) hydraulic leveling jacks
1986 Ford LN-8000 tandem axle chassis P/B 3408 Cat & 13 Speed transmission.
1219-3 Gus Pech H-48 1978 Super George--100' Quad kelly--48" ring gear--All Hydraulic driven--3408 Cat deck engine--(3) hydraulic leveling jacks 1993 Ford L-9000 tandem axle chassis P/B 350 Cummins & 10 Speed Transmission
1250-1 Ideco H-20   DEEP BIG HOLE WATER WELL PACKAGE
MAST: 92' square tube telecoping mast w/stabbing board, Hydraulically raised and cable scoped, (Can make mouse hole connections)--DRAWWORKS: Ideco H-20 SN 410 single drum drawworks w/6 part 1" lines--60 Series Detroit and 5 speed Allison transmission.
ROTATING EQUIPMENT:
17 1/2" Oilwell rotary table
3" x 34' kelly & roller bushing
4" kelly hose
Swivel, 135 ton w/4" opening. (8000' since new)
SUBSTRUCTURE: 10' H (8' clearance under table) with ramp and swing out sides and beaver tail.
MUD PUMPS:
#1: GD FXZ 7 1/4 x 12 duplex p/b twin 671 Detroit diesels
#2: GD 7 1/4 x 16 duplex with all new gear end. No power.
MUD SYSTEM:
240 bbl tank w/shaker, desander and centrifugal pump.
255 bbl suction tank w/desilter and centrifugal pump and mixer hopper. 2 pit stir.
GENERATOR:125KW p/b 3406 Cat
TUBULARS: Approx. 5400' used
3 1/2" x 3 1/2IF tool joint drill pipe, 3200' is 15.50 lb. (1) hole since double white band inspection, 2200' is 13.30 lb and is yellow band.
(7) 6" drill collars.
HANDLING TOOLS:
(2) type C tongs w/extra heads
Drill pipe and collar elevators and slips--Elevator links--pickup subs--crossover subs--Pipe spinner--Bear automatic driller--Rat hole digger--Water tank--Fuel tank--Doghouse-Parts room w/air compressor and new water pump.
BOP EQUIPMENT: None
Drawworks and mast are tandem axle trailer mounted. All other equipment is oilfield skid.
1207-4 IR T-3W 1990 COMPLETE PACKAGE!
850/350 air--Cummins deck engine--34' mast--Single rod loader--Water injection system--DTH oiler--(3) hydraulic leveling jacks--No mud pump.
INCLUDED WITH RIG:
500' NEW 4 1/2 x 20' drill pipe
500' used 4 1/2 x 20' drill pipe.
1989 Ford 9000 tandem axle chassis p/b Cummins diesel and 10 speed transmission w/ 1800 gal. flat top water bed.
Misc. subs and pipe handling tools.
1989 Ford F-9000 tandem axle chassis with rebuilt Cummins engine & 10 speed transmission.
819-14 IR T-3W 2000 900/350 air--C-15 Cat diesel deck engine--3 x 4 Mission Magnum centrifugal mud pump--33' mast--(4) hyd. Leveling jacks--Water injection-- DTH oiler 8054 hours

INCLUDED WITH RIG:
300' used 4 1/2 x 20' drill pipe.
1999 IHC model 2564 tandem axle chassis p/b C-12 Cat diesel engine.
791-2 IR T-4W 1994 900/350 rebuilt air compressor--50,000 pullback--KTA19-C rebuilt Cummins deck engine--Worm gear head--(2) winches--(3) cyl. Cat water injection--Electric oiler--(3) hyd leveling jacks--
Air compressor rebuilt (5000 hrs)--Deck engine new rebuild w/receipts.
1994 Crane Carrier Corp. tandem axle chassis with L-10 Cummins. Near new tires all around.
1186-1 IR T-4W 1984 900/350 air--70,000 pullback--12V71 Detroit deck engine--4 1/2 x 25' carousel--Spur gear head--(3) hydraulic leveling jacks--Water injection--DTH oiler--

INCLUDED WITH RIG:
Approx. 1600' used 4 1/2 x 25' x 2 7/8IF tool joint drill pipe
(2) used 6" DTH hammers
(1) spare top head motor
1984 tandem axle Crane Carrier Corp. chassis w/3208 Cat and 13 speed transmission--Tires 60% plus
819-15 IR T-4W 1998 900/350 air--QSK Cummins deck engine--33' mast--50,000 pullback--4 1/2 x 25' carousel--(3) hyd. Leveling jacks--Worm gear head--5698 hours

INCLUDED WITH RIG:
300' used 4 1/2 x 25' drill pipe.
1998 tandem axle Crane Carrier Corp. chassis
1274-1 IR TH-60 1979 MUD & AIR TOPHEAD
750/250 air--3 x 4 Centrifugal mud pump--Cat 25 gpm water injection system--Sandline drum--32,000 lb winch (double line)--Night lights--
Newly rebuilt engine and radiator--New style Cotta box
1979 IHC Paystar 5000 p/b 8V92 Detroit diesel.
401-6 IR TH-60 1999 825/350 air(new rebuild)--3 x 4 Mission Magnum centrifugal pump--30,000 pullback--18,000 lb. hoist line--2000 lb. sand line--Water injection--DTH oiler--(4) hyd. Leveling jacks--11,615 hours 1999 IHC 5000 tandem axle chassis with 3406E engine--16,000 miles 1999 IHC 5000 tandem axle chassis with 3406E engine--16,000 miles
401-7 IR TH-60 2001 1050/350 air (1250 hrs. since ribuilt)--3 x 4 Mission Magnum centrifugal mud pump--25 gpm water injection--DTH oiler--30,000 pullback--18,000 Hoist line--2000 lb. sandline--(4) hyd. Leveling jacks--10,700 hours 2001 IHC 5600 tandem axle chassis w/C-16 Cat engine--11,900 miles.
1267-4 Logging Truck Aries Video Camera 2004 2004 Aeries Video logging truck--5000' power reel--SEE pictures & call for more details. 307-587-5192 2004 Ford diesel with ambulance van body.
1232-1 Longyear 34   Longyear 34--Bean 35 pump p/b gasoline motor through 3 speed transmission--Angle hole capable (head rotates 180 degrees)--
INCLUDED WITH RIG:
Cat head and wirelinge winch w/3000' cable--Skid mounted.
AVAILABLE AT EXTRA COST:
Approx. 1500 ft. + B Rods
Some H rods
Some casing
Core barrels (some w/split innertubes)
Specialty Tools
A complete inventory will be available soon.
Military 6 x 6 mounted by Longyear in 1972.
1276-1 Mayhew 1000 1973 NICE REBUILT 1000!
5 x 6 GD mud pump--580 cfm x 50 psi GD drilling or development air compressor--32' mast--23' kelly--Single sheave traveling blocks--2" swivel--7 1/2" non retractable rotary table--Vari-draulic chain pulldowns--Side pipe rack and fast slide for 20' pipe--Platforms--SN:10-2224

MANY REBUILDS
Many new parts and repairs including but not limited to: New cables both drums--New mud pump expendables--New mud pump clutch--New mud pump drive sprockets--Rebuilt swivel--Some new hydraulic hoses--Kelly Bushing built up--New mud pump suction hose--New crown sheave bearings--New truck clutch--New paint--Many misc. truck repairs including guages, lights, Transfer case seals--battery, floor mats, air pressure tank etc. etc.
INCLUDED WITH RIG:
180' 2 3/8" Mayhew Regular drill pipe.
200' 2 7/8" drill pipe
(1) each used mill tooth tricone bits sizes 3", 4" 5" & 6".
(1) new mill tooth tricone 9" bit
(1) 4 1/2" reg. bit sub
(2) new 6" bits
Portable mud pit
Mud hoses
5" air hammer and drive plate to drive 6" casing.
1973 IHC Fleetstar 2010-A tandem axle chassis p/b 345 V/8 gasoline/propane engine and 5 x 2 transmissions. New front tires.
1230-3 Mobile B-90 1994 Mobile B-90--IR 400/200 screw compressor--6 cyl. Cummins deck engine (500 hours on rebuild)--3L8 Moyno pump--(3 winches)--Safety Hammer--(4) Hyd. Leveling jacks--(2) auger racks. (#D-401)
Deck engine rebuilt 500 hrs.
1992 Ford LT-8000 tandem axle chassis w/Cummins engine and Fuller 13 speed trans. (#HT-502)
819-23 Mobile B-47   3" Moyno pump--3 cylinder Deutz diesel deck engine--Wiggle tail head--Hyd. Leveling jacks--Hoist line--(1) cathead--Pipe rack
INCLUDED WITH RIG:
200' 2 5/8" x 5' sections Mobile Lock drill pipe.
GMC Top Kick single axle chassis with Cat diesel engine.
424-5 Pipe Trailer   2003 2003 Fabrication Technologies tandem axle dual wheel pipe trailer. Custom made with pipe slide for Range II drill pipe. Like new condition.
(Pipe not included)
 
819-26 Portadrill 522 (1500 Class) 1972 EXCELLENT URANIUM RIG
5 1/2 x 8 GD mud pump--36' mast--Bailing drum (no cable)--3 1/2 x 24' fluted kelly--2" swivel--Hydraulic pull downs--7 1/2" retractable rotary table w/5" mater bushing--(5) speed table transmission-- (2) part line both drums--Side pipe rack for 20' pipe-- Operators and helpers platforms.
AVAILABLE AT EXTRA COST:
400' used 2 7/8" x 20' x 2 3/8"IF tool joint drill pipe. ADD: $4000.
MANY RECENT REBUILDS: New kelly and bushing 2012--Power/chain case rebuilt by Portadrill 2009--Rotary table rebuilt by Portadrill 2010--Mud pump gear end inspected 2013 by qualified technicion and stated to be 85% of new--Rig was sanded and primed 2009 but never painted.
1984 Autocar tandem axle chassis with 3208 Cat diesel engine
1165-1 Portadrill TKS 1978 750/250 Sullair twin screw compressor--8V92T Detroit diesel deck engine--Hydrastatic powered double drum drawworks w/power up/down operation for infinite control of drill string--Sandline drum--7 1/2" retractable rotary table--4 1/2" x 24' gfluted kelly--2 1/2" opening swivel--Pulldowns--(3) hydraulic leveling jacks--Hyd. Water injection--DTH oiler--
INCLUDED WITH RIG:
(1) Used down hole hammer drill
(1) dog house w/geolograph machine
(1) 1000 gal. fiberglass water tank on skid w/Kerr duplex pump for mud mixing.
(1) pipe trailer
(1) mixed lot of misc. tools and bits.
No drill pipe avail.
Compressor will not rotate--Cleaned and Painted.
1977 IHC Paystar 5000 tandem axle chassis p/b 3208 Cat diesel and 13 speed transmission. 20,500 miles.
1094-3 Portadrill TKT Prospector 1977 REBUILT ON (4) AXLE IHC

7 ½ x 10” GD mud pump—LeRoi model 256S2 air compressor (500 cfm @ 250 psi)—53’ mast—Double drum drawworks w/hydrastic up/down power—7 ½” hydrastatic powered retractable rotary table—(4) hydraulic leveling jacks--(2) 30 ton McKissick traveling blocks
Rig is mounted on and powered by (4) axle twin steer IHC Paystar 5000 chassis with Cummins diesel engine
1197-2 Portadrill 10-TG retro 1967 CONVERTED TO TOPHEAD DRIVE--
500/250 model 256S2 LeRoi air compressor--671 Detroit deck engine--Cyclone tophead--Water injection--Operators and helpers platforms--Side pipe rack--Bailing drum--(3) hydraulic leveling jacks.

AVAILABLE AT EXTRA COST:
Weldco-Beale model 915 casing hammer w/cylinder type handling package.
1967 IHC tandem axle chassis with 549 gasoline engine and 5 x 4 transmissions.
826-1 Portadrill 10-TK 1973 500/250 air (LeRoi 256S2 compressor)--8V71T Detroit diesel deck engine--All hydrastatic powered drawworks and rotary table--7 1/2" retractable rotary table--Sandline drum--38' mast--(4) part lines--2 1/2" opening swivel--4 1/2" x 24' fluted kelly-- Bean 2 cylinder water injection system--Side pipe rack for 20' pipe--(3) hydraulic leveling jacks--Operators and helpers platforms
AVAILABLE AT EXTRA COST: (call for pricing)
MUD PUMP: 5 x 8 GD duplex high pressure chain drive p/b 671 Detroit and 4 speed transmission--skid mounted on 1981 Homemade trailer.
DRILL PIPE: Approx. 1560' 3 1/2 x 20' x 2 3/8IF drill pipe.
(2) 4" x 20' drill collars
(1) 10 3/4" hole opener
(1) 6" model QL60IR down hole hammer drill w/6" bit.
(1) 500/250 LeRoi compressor package p/b 671 Detroit--skid mounted.
1973 Ford 9000 tandem axle chassis.
826-3 Portadrill 10-TKT 1975 53' mast w/stabbing board--750/250 air (1) Leroi 256S2 500/250) and (1) Leroi 253S2 250/250 compressors--Hydrastatic powered double drum drawworks w/power up/power down feature--(4) part lines both drums--Bailing drum--7 1/2" retractable rotary table--3 1/2" x 24' fluted kelly--(3) hydraulic leveling jacks--water injection system--Side pipe rack for 20' pipe--Operators and helpers platforms.
AVAILABLE AT EXTRA COST: (call for pricing)
MUD PUMP: 5 x 10 GD duplex p/b 471 Detroit--skid mounted
DRILL PIPE: Approx. 1560' 3 1/2 x 20' x 2 3/8IF drill pipe.
(2) 4" x 20' drill collars
(1) 10 3/4" hole opener
1975 IHC Paystar 5000 tandem axle chassis with 425 hp Cat engine.
401-4 Portadrill 10-TK 1972 600/125 Air--3 X 4 pump--Hydrastatically powered drawworks and rotary table--8V71N Detroit diesel deck engine--(3) hyd. Leveling jacks--Side pipe rack--4 1/2" X 24' kelly--7 1/2" retractable rotary table--Water injection 1972 IHC M-623 tandem axle chassis. DT-466 IHC diesel
1197-1 Portadrill 10-TL 1973 EXCELLENT CLEAN RIG
70,000 pullback (6" hoist cylinders)--Tophead drive--500/250 air--Bailing drum--Hydrastat powered drawworks with power up and down feature--(2) cylinder Bean water injection system--DTH oiler--Operators and helpeers platforms--Hydrulic breakout tong.

AVAILABLE AT EXTRA COST:
Casing Hammer--915 Weldco-Beale model 915 with hydraulic cylinder handling package--
1973 IHC Paystar tandem axle chassis with 549 gasoline engine.
1237-2 Pump Hoist Smeal 5-T 1995 NICE UNIT!
(3) scope extended boom for windmill service applications. It can operate in standard position or extend up for lighter lifts--Bailing drum (no cable)--(2) rear jacks--Remote control pendant--Hydraulic quick couplers at rear for accessory hook up--(1) pipe rack
1995 Ford F-350 1 ton truck with nice Omaha tool bed. V8 gas engine and 5 speed transmission 100,000 total miles.
1227-1 Pump Hoist Shopbuilt   A CHEAP FIXER-UPPER!
Shopbuilt unit--30,000 lb. capacity--Jager Mfg.double drum drawworks--6 part lines on main drum--6 cylinder IHC propane deck engine--Cathead--(2) rear hydraulic leveling jacks.
1978 Chevrolet C60 tandem axle chassis w/350 gasoline engine.
1225-1 Reichdrill T-690 1999 900/350 air--30,000 pullback--High Torque (2) motor tophead--(2) winches--Carousel--485 HP Cat deck engine--Approx. 6500 hrs. 1999 Freightliner tandem axle chassis
1245-1 Reichdrill T-650WII 2000 GREAT BUY!
900/350 air--40,000 pullback--3406 Cat deck engine--8 pod 4 1/2" x 20' carousel--18 gpm Bean water injection--Retractable table plate--Breakout wrench--(3) hydraulic leveling jacks--No mud pump--Approx. 9000 hours.
2000 Freightliner tandem axle chassis P/B 3406 Cat--55,000 miles.
1041-1 Reichdrill T-650-WII 2004 PRICE REDUCED!
ONLY 3300 HOURS 4/2011!
2004 Reichdrill Model T-650-WII

Hour Meter - 3300 Hours
-Rotary Head 0-108 RPM @57,200 lb. - in. torque w/nylon guide
-1000 CFM and 350 PSI Sullair compressor
-500 HP CAT Model 3406C Mechanical Engine
-Compressor variable volume control
-MESABI removable tube type cooler for operation up to 100 deg. F ambiant temperature
- 38,000 lb. hoist
- 27,000 lb. pulldown pressure
-Mast 34 ft. with 28ft. Stroke
-18" table opening
-7,000 lb. Winch with hydraulic extendible & rotating jib boom
-Rotation torque limit control
-air operated holding wrench mounted in mast
-Hydraulic cylinder with rigid wrench mounted in mast
-Three leveling jacks, 1-48" stroke front, 2-36" stroke rear
-15 pc. Rod box
- 300' of drill steel
-Drill pipe lifting rod
- 4" split table bushing
-Spindle sub
-Night Lights
-Air pressure regulator
-Fuel Capacity - 140 gallon
- one 36" steel tool box
-9-pod barrel loader for 4" x20" pipe Reichdrill Style
-20GPM water injection pump
-Auxiliary remote helper's controls (wireless)
-Auxiliary blowdown system
-Air line lubricator, 8 gallon
-Aluminum vandal cover
-Platforms & Walkway group, folding
-(1) Hammer holder - for 8" hammer
-(1) Hammer holder - for 6" hammer
-Holes in top head for lifting casing
- Weld stops for "J" Wrench
-Sealed beam lights on rig & truck
-Heavy duty side tool box - steel
-Truck frame to be extended to allow 22 inches betweeb truck cab and cooler assembly- for welder or rig box.
-Capacity to tie two rigs together for more air.
-Exhaust wrap (standard)
-Cat Walks on machine- wide walk ways
-Water injection pump to be mounted on operator's side of drill
-Fuel tank and tool box to be mounted as high as possible.
-Truck will have Henderson Suspension with Rockwell rear ends
 

Mounted on 2004 Mack Granite 6x4  with Mack 460 HP Diesel Engine w/1450 Lb. Ft. Torque; Fuller RTLO Transmission, Jake Brake, 20,000 Lb. front axle, 46,000 lb. rear axle, Hendrickson RS460 Block suspension, controlled differential lock, AM/FM cassette, airconditioning, air dryer, 10 polished aluminum wheels, 75 gallon aluminum fuel tank. Truck has Rockwell rears- (Mileage 6300)
1041-2 Reichdrill T-650-WII 2005 PRICE REDUCED!
ONLY 1920 HOURS 4/2011!
2005 Reichdrill Model T-650-WII

Hour Meter - 1920 Hours
-Rotary Head 0-108 RPM @57,200 lb. - in. torque w/nylon guide
-1000 CFM and 350 PSI Sullair compressor
-500 HP CAT Model 3406C Mechanical Engine
-Compressor variable volume control
-MESABI removable tube type cooler for operation up to 100 deg. F ambiant temperature
- 38,000 lb. hoist
- 27,000 lb. pulldown pressure
-Mast 34 ft. with 28ft. Stroke
-18" table opening
-7,000 lb. Winch with hydraulic extendible & rotating jib boom
-Rotation torque limit control
-air operated holding wrench mounted in mast
-Hydraulic cylinder with rigid wrench mounted in mast
-Three leveling jacks, 1-48" stroke front, 2-36" stroke rear
-15 pc. Rod box
- 300' of drill steel
-Drill pipe lifting rod
- 4" split table bushing
-Spindle sub
-Night Lights
-Air pressure regulator
-Fuel Capacity - 140 gallon
- one 36" steel tool box
-9-pod barrel loader for 4" x20" pipe Reichdrill Style
-20GPM water injection pump
-Auxiliary remote helper's controls (wireless)
-Auxiliary blowdown system
-Air line lubricator, 8 gallon
-Aluminum vandal cover
-Platforms & Walkway group, folding
-(1) Hammer holder - for 8" hammer
-(1) Hammer holder - for 6" hammer
-Holes in top head for lifting casing
- Weld stops for "J" Wrench
-Sealed beam lights on rig & truck
-Heavy duty side tool box - steel
-Truck frame to be extended to allow 22 inches betweeb truck cab and cooler assembly- for welder or rig box.
-Capacity to tie two rigs together for more air.
-Exhaust wrap (standard)
-Cat Walks on machine- wide walk ways
-Water injection pump to be mounted on operator's side of drill
-Fuel tank and tool box to be mounted as high as possible.
-Truck will have Henderson Suspension with Rockwell rear ends
 

Mounted on 2004 Mack Granite 6x4  with Mack 460 HP Diesel Engine w/1450 Lb. Ft. Torque; Fuller RTLO Transmission, Jake Brake, 20,000 Lb. front axle, 46,000 lb. rear axle, Hendrickson RS460 Block suspension, controlled differential lock, AM/FM cassette, airconditioning, air dryer, 10 polished aluminum wheels, 75 gallon aluminum fuel tank. Truck has Rockwell rears- (Mileage 6300)
             
1208-1 Robbins T-37 1975 EXTREMELY HIGH TORQUE TOPHEAD DRIVE
850/150 air--30,000 pullback--50,000 pull down--Mechanical quill tophead drive for extremely high torque drilling--Carousel--Hyd. Leveling jacks.

Engine was rebuilt in 2001 and unit has not drilled since. Rig was ran through company shop in July 2011 and following is the report: Engine was strong with no apparent problems. Truck Transmission gears were good--Mast raised properly and tophead rotation was confirmed to be ok--No apparent major hydraulic or air leaks.
1975 (4) axle crane carrier chassis with 350 Cummins
1242-1 Schramm T-300M 2003 3 x 4 Mission centrifugal pump--Hydraulic driven 400/200 Sullair compressor--(4) cylinder Bean water injection (25 gpm)--Carousel for 3 1/2" drill pipe--(3) hydraulic leveling jacks--Breakout cylinder--Approx. 9000 hours.

INCLUDED WITH RIG:
300' used 3 1/2" x 20' x 2 3/8IF tool joint drill pipe--Portable mud tub.
2003 IHC Model 7400 6 x 6 tandem axle chassis p/b HT350 IHC engine and 7 speed transmission--14,000 lb front axle and 40,000 rear axles--54,000 GVWR. Approx. 29,000 miles.
1175-1 Schramm T-450W 1995 COMPLETE REBUILT CASING HAMMER UNIT
EXTRA NICE 825/350 GHH model CF-1000H compressor w/clutch--Series 60 Detroit diesel w/ADM Electronic Module--30,000 pullback--28.5' head travel--Single motor tophead--floating sub--4 1/2" x 20' x (6) pod carousel--10,000 lb. winch--Hyd. Jib boom--DTH oiler--25 gpm Cat water injection system--Side pipe rack--(3) hydraulic leveling jacks--Engine heater--60" breakout wrench--Plumbing for mud pump operations--
INCLUDED WITH RIG:
CASING HAMMER: 2007 Atlas R2000 Hydraulic casing hammer complete w/mast guides--swing-jib, Hydraulic cylinder handling package which can drive 6", 8", 10", & 12" casing.
DRILL PIPE: 500' good used 4 1/2 x 20' x 3 1/2" reg, drill pipe--
500' good used 3 12/ x 20' x 2 3/8IF.
UNDERREAMER SYSTEM:
Geo Rockford XS drill system--Numa Super+Jaw-Casing Retractor
HAMMER:(1) used 6" IR QL60
MISC: bits, subs, stabilizers & tools.
REBUILDS, Deck engine, new rebuild 2012--GHH compressor new rebuilt 2011--All hyd. Hoses--2 new Hyd. Pumps new 2012--New pulldown chains & sprockets 2007--Lincoln Lubricator new 2007--Radiator--Oil Cooler new core 2010--New compressor clutch 2009--Breakout table and slips new and rebuilt--Casing hammer hoist cable--New Paint
Rig is mounted on 1995 Ford L-8000 w/Cummins FD1460 diesel engine and 10 speed Eaton Transmission--Approx. 43,000 mi.
1261-1 Schramm T-450WS 2000 900/350 Air--3406 Cat deck engine--No carousel--(3) hydraulic leveling jacks--water injection--Side pipe rack for 20' pipe--6334 Total Hours.
AVAILABLE AT EXTRA COST (Call for pricing):
Atlas hydraulic casing hammer and hydraulic cylinder handling package.
2000 IHC Navistar 2564 tandem axle chassis w/International Diesel 530EHT (330HP)--48,500 miles.
1235-1 Schramm T-64 1964/1997 900/350 air priced right!
1964 T-64 refabricated and retrofitted in 1997: 900/350 Sullair twin screw compressor--3406 Cat deck engine--28,000 pullback--Belco Hydraulic welder--10,000 lb. and 2,000 lb. hydraulic winches--3L6 Moyno pump--(4)hyd. Leveling jacks--Bean (2) cylinder water injection system--6111 hours since 1997 refurbish and retrofit--Owners and shop manuals included.
INCLUDED WITH RIG:
? Ft. 4 1/2" x 20' x 3 1/2 reg. tool joint drill pipe.
(1) each good used 5" and 6" down the hole hammer drills.
1985 IHC model 2500 tandem axle chassis 350 big cam Cummins-20,000 lb. front axle w/double box power steering--Aluminum wheels--(2) 115 gal. fuel tanks.
Flotation tires in front.
1237-1 Schramm T-64 1974 GREAT STARTER PACKAGE W/ALL THE ACCESSORIES
Standard T-64 tophead drive rig--450/250 Schramm piston compressor (camshaft is out)--8V71 Detroit diesel deck engine--water injection--(3) Hyd. Leveling jacks--No carousel--
Extra compressor that could be mounted in place of the compressor on the rig.
INCLUDED WITH RIG AS A PACKAGE:
SPARE COMPRESSOR: Extra Schramm compressor that would fit on rig in lieu of the inoperable one.
DRILL PIPE: 37 pieces 758') 4 1/2 x 20'6" x 3 1/2 reg tool joint
8 pieces (120' 4 1/2" x 15' x 3 1/2 reg. tool joint. Total pipe 878'
10 pieces (50') 2 3/8" x 5' NW Rod drill pipe
AUGERS: 10 pieces (50') 4" x 5' hollow stem.(1) Hammer split spoon--(1) split spoon sampler
SUBS: (1) 2 1/2 x 3 x 4 1/2 x 18" box sub to NW Rod and augers.
(1) Auger plug pickup for NW Rod.
(1) 3 1/2 reg pin x 6 5/8 reg box bit sub w/ good used 12 1/4" button bit
(1) 3 1/2" reg box x box bit sub w/6" button tricone bit.
(1) 3 1/2 reg. box x 4 1/2 reg box x 24" bit sub w/7 7/8" tricone bit
(1) 3 1/2 reg box x 2 7/8" reg box bit sub w/5" bit
(1) used 3 1/2" x 3 1/2" box to box bit sub.
(1) new 3 1/2" x 3 1/2" box to box bit sub.
(1) 3 1/2" reg box x 1" NPT pipe sub
(1) 3 1/2" reg box pickup plug
(1) 3 1/2" reg pin pickup plug
(1) 3 1/2 reg x 5' sub
DOWN THE HOLE HAMMERS & BITS:
(1) used 6" hammer w/6" button bit
(1) used 5" hammer w/5" bit
(1) 10" hammer bit (slightly used)
(1) used 8" hammer bit
TRICONE BITS:
(2) New 6' button bits
(1) New 6" drag bit
(1) New 8" drag bit
(1) New 9 7/8 Tricone Mill Tooth Bit
(1) used 7 7/8" Tricone Mill Tooth Bit
(1) 7 7/8" Tricone button bit (used to ream 40' of hole)
(2) used 6" drag bits
MISC. ITEMS:
(3) well head diverters (1) each 6", 8", & 10".
(3) pipe alignments clamps
(2) 4 1/2" PVC elevators (shopbuilt)
(2) 4" PVC elevators (shopbuilt)
(4) 6" pipe elevators
(1) 8" pipe elevators
(1) breakout wrench
(1) Drill pipe handler elevator
(1) 3" Wilden air diaphram mud/grout pump.
(2) spare Schramm air compressor blocks
(1) spare Schramm air compressor head
(1) each inner and coolers.
Mixed lot of clutch parts
(1) 3" x 5" tapertap
(1) used Mills knife casing perforator.
1974 GMC tandem axle chassis with V8 gas engine and 5 x 3 transmission.
1230-4 Simco 2800 2008 PTO driven--4,000 ft. lbs torque--(2) winches--(3) hydaulic leveling jacks--Automatic Hammer--3L6 Moyno pump--1725 total hours. (#D-202)
INCLUDED WITH RIG:
(10) pieces (100’) used NW x 10’ drill rod
(6) pieces (30’) used 4 Ό” Mobile Lock HS augers
(1) used auger cutter head
(1) used adapter cap from tophead to augers
(1) Cross over sub NWJ box x NW pin (tophead to drill rod)
(1) Cross over sub NW box x 2 3/8 reg. (box drill rod to bit)
(1) Cross over sub NW box x AWJ pin (drill rod to split spoon)
 2008 Ford F-550-XL chassis with 6.0 liter Power Stroke diesel & 6 speed manual transmission--34,000 miles.
1072-1 Simco 5000 1979 3 x 4 centrifugal mud pump--(2) winches--Tophead drive--(2) rear hydraulic leveling jacks--Side pipe rack for 15' pipe w/fast slide--300 CID Ford gas deck engine--Operators and helpers platforms--Wilden 2 x 3 air driven grout pump 1979 Ford L-9000 tandem axle chassis with 3208 Cat diesel engine--Air brakes.
1207-1 Simco 5000 1978 Tophead Drive--3 x 4 Mission centrifugal mud pump--160 cfm @ 125 psi Sullair screw development air compressor--Hydraulic hoist line drum--Ford 6 cyl. Diesel deck engine--(3) hydraulic leveling jacks--Side Pipe Rack for 15' pipe.
INCLUDED WITH RIG:
(17) pieces (255') used 2 7/8 x 15' drill pipe.
(1) used 6" stabalizer
(1) used 8" stabalizer
1978 IHC 1750 single axle chassis with DT-466 diesel engine
1184-1 Speedstar 30-K 1985 840/350 air--30,000 pullback--DTH oiler--Side pipe rack w/fast slide--Hyd. Water injection--(4) hydraulic leveling jacks--No mud pump (see note)--Sandline drum--32' mast--18,000 lb. winch--Hydraulic pipe spinner--Operators and helpers platforms.
INCLUDED WITH RIG:
400' 4 1/2 x 20' drill pipe
(1) used 6" IR 360 down the hole hammer.
AVAILABLE AT EXTRA COST:
IHC single axle water truck with 1000 gal flat top water tank. ADD: $12,500
1985 Loadcraft crane carrier w/475 hp. Twin turbo Cummins diesel engine.
1222-3 Speedstar 70-K 1982 TOPHEAD MUD RIG
7 1/2 x 10 GD FO-FXO mud pump--70,000 pullback--No air--Tophead w/single hydraulic motor 10,000 ft. lbs. torque--Extended mast can run range III casing--(4) part 3/4" line on (2) speed hydraulic hoist (can pull 125,000 lbs)--Single stem loader--Pipe spinner
1982 (4) axle Crane Carrier w/KT Cummins engine Call 307-587-5192
1185-1 Speedstar 70-K 1982 900/350 GHH--70,000 pullback--Tophead drive--42' x 100,000 lb. capacity mast--8V92TA deck engine--Cat water injection--Hydraulic auxillary winch--(4) hydraulic leveling jacks--(2) hydraulic break out cylinders--Hydraulic pipe spinner.
1982 (4) axle Crane Carrier Corp. chassis p/b 8V71 Detroit and 9 speed transmission with deep reduction gears.
957-6 Speedstar 71 1966 22.2 TOTAL HOURS!
Speedstar 71 cable tool with rotary attachment--Hercules diesel engine--
(4) wheel wagon--
819-10  Speedstar SD-50 1992 GEOTHERMAL SPECIAL!!

5 x 6 GD mud pump--300/200 Sullair screw air compressor--Tophead drive--Side pipe rack--Hydraulic walking beam--32' mast--(4) hydraulic leveling jacks--Operators and helpers platforms--Air controls.

Rig is stated to be in EXCELLENT condition but could use paint.
1993 IHC model 4800 4 x 4 single axle chassis.   
1230-7 Speedstar
Stratastar
SS-10 1994 PTO driven Speedstar Stratastar SS-10--11,000 ft. lbs. torque--(2) winches--(3) hydraulic leveling jacks--Safety Hammer--(2) auger racks--Hydraulic break out wrench--10,050 total hours.
(#D-301)
1994 Ford F-800 single axle chassis with Cummins diesel engine, 5 speed trans. And 2 speed rear end--174,000 miles.
(#HT-503)
1243-1  Speedstar SS-15THH 1977 $60,000 WITH CASING HAMMER & ALL TOOLS
Tophead drive--450/250 LeRoi air compressor--38' mast--Water injection system--Pulldowns--No DTH oiler or mud pump--(3) hydraulic leveling jacks--Operators and helpers platforms.
Rig originally had a 5 x 6 GD mud pump mounted w/direct drive so another mud pump could be mounted on it. 

INCLUDED WITH RIG:
(1) used 6" hammer (50%)
(1) used 5" hammer (75% good)
Drill Pipe: Approx. 600' used 4 1/2 x 20' x 2 7/8IF tool joint.
(1) 8" stabalizer
(6) various sized subs
Misc. pipe handling tools. 
1977 tandem axle Crane Carrier with rebuilt 350 Cummins & 13 Speed Transmission.   
1122-2 Speedstar SS-15III 1977 Tophead drive--500/250 air (LeRoi 256S2 compressor)--3 x 4 centrifugal mud pump--Pullmaster hydraulic winch--38' mast--Myers water injection--(4) hyd. Leveling jacks--Side pipe rack and fast slide for 20' pipe--300' used 3 1/2 x 20' x 2 3/8IF tool joint drill pipe. 1977 GMC tandem axle chassis with 290 Cummins and 9 speed transmission.
1076-1 Speedstar SS-15iii 1978 BUY NOW $47,500!
750/350 Sullair--Tophead drive--38' mast--Water injection--DTH Oiler--Plumbed for mud--Operators and helpers platforms--Casing hammer cylinder type handling package (no casing hammer included)
Compressor has 40 hours operation since MOH.
1978 tandem axle Crane Carrier Corp. chassis with 400 Cummins diesel engine.
1222-2 Speedstar SS-22HDM 1980 54' X 75,000 lb. working capacity mast w/ stabbing board set up for double 20' stands--GD FO-FXO 7 1/4 X 10" mud pump--Double Drum Drawworks w/6" x 24" double brake bands on each drum--18" (2) plate air clutches--Hydraulic pulldowns--10" retractable rotary table--4 1/2" x 24' kelly--(4) hydraulic leveling jacks--
INCLUDED WITH RIG:
1000' used 3 1/2 x 20' x 3 1/2IF tool joint drill pipe
1980 (4) axle Crane Carrier chassis w/N-14 electronic Cummins and 10 speed trans.
1252-1 Speedstar SS-40-SP 1982 BARE RIG OR PACKAGE!
63’ mast, (3) drum drawworks with air clutches, (6) part lines both main drums, p/b 6V-71 Detroit diesel and 653 Allison transmission, 27” opening rotary table, 6 x 6 Gorman-Rupp centrifugal pump p/b 471 Detroit diesel, Weight indicator, tongs, 4 Ό” x 40’ hex kelly w/roller bushing, King 60PG swivel, Kelly hose, (2) hydraulic winches, (5) hydraulic leveling jacks.
AVAILABLE AT EXTRA COST AS SHOWN:
National C-250 6 ½” x 15” duplex mud pump w/high pressure fluid end and screw caps p/b D-350 Cat, includes air controls, suction hose, mud hopper, mounted on oilfield skid $35,000
Emsco DA-500 5 ½” x 16” duplex mud pump w/high pressure fluid end and screw caps p/b D-353 Cat, air controls, mounted on oilfield skid $45,000
1981 Western Star (3) rear axle winch truck p/b 400 Cummins w/long rig up bed, live tail roll and 50 to Braden winch $30,000
1990 KW tandem axle tractor p/b 400 Cummins $20,000
1985 GMC tandem axle chassis p/b Cummins diesel complete w/65 bbl. vacuum tank & vacuum pump $15,500
Freightliner truck w/25 ton winch $12,500
1982 Ford dog house $3,000
1953 Hobbs tandem axle pipe trailer $2,500
1955 Lacro drop deck trailer 27’ 7” well $ 5,500
Allight light tower p/b Cat diesel $ 6,000
(29) pieces of 4” double white band drill pipe @ $30 per ft. $27,000
(68) pieces of 4” yellow band drill pipe @ $22 per ft. $46,200
(8) 6 Ό” x 26 ½ to 28’ x 4 ½ FH drill collars @ $1000 ea. $ 8,000
Misc. extra parts, subs, drill pipe and casing handling equip. $10,000
(4) axle Crane Carrier p/b 400 big cam Cummins
999-1 Speedstar Mini-Star 1990 EXCELLENT LIGHT WEIGHT GEOTHERMAL RIG

220 cfm @ 225 psi Sullair compressor--4 1/2 x 5 GD mud pump--Tophead drive--John Deere 4 cylinder deck engine--Single stem loader--Side pipe rack for 20' drill pipe--(2) winches--
1990 IHC single axle chassis
732-22 Trailer Freuhauf 1975 1975 Fruehauf tandem axle drop deck trailer (RGN) w/hydraulically operated removable gooseneck.  
732-21 Trailer Lufkin 1971 40' tandem axle oilfield float w/rolling tailboard.  
732-24 Trailer Trailmobile 1969 1969 Trailmobile Van 27' trailer.    
706-5 Walker-Neer 250-40 1980 COMPLETE RECENTLY REFURBISHED AND READY TO DRILL!!
DRAWWORKS - APACHE WALKER-NEER, 250-40, 450 HP, , LEBUS GROOVED, 1" LINE,
AIR DRILLER'S CONTROLS, RIGHT ANGLE DRIVE SINGLE ENGINE COMPOUND W/ AIR
CLUTCH AND BRAKE. P/B 3408 CAT AND CLT754 ALLISON TRANSMISSION W/BENNET
ELECTRIC/OVER AIR SHIFTER, WEIGHT INDICATOR, TULSA PULLDOWN WINCH, 12"
DIRECTIONAL DRILLING BACK BRAKE.

MAST, 58' APACHE WALKER-NEER SINGLE LAY DOWN MAST, 200,000# STATIC HOOK
LOAD, CROWN BLOCK, FASTLINE SHEAVES, 1" LINE, 4" STANDPIPE, LADDER DERRICK
CLIMBER.

HYDRAULIC PIPE HANDLING BOOM.

SUBSTRUCTURE: 4' H SHOP BUILT WITH NEW 5' X 10' STEEL FLIP UP STEEL RAMP.

TOPHEAD DRIVE: 150 TON APACHE.

MUD PUMPS:
#1 EMSCO DA-500 WITH FORGED STEEL END. P/B C-15 CAT W/AIR STARTER.
#2 EMSCO DA-500 W/FORGED STEEL FLUID END, PULSATION DAMPNER, PRESSURE
GUAGE, P/B 353 CAT, 4 X 5 MISSION 50 HP CHARGE PUMP

MUD TANKS: 220 BBL (10'W X 33'L X 5'H) W/ DOUBLE SCREEN SHAKER, DESANDER
CONE, 4 X 5 MISSION 50 HP PUMP, MUD MIXING HOPPER.

BOP EQUIPMENT: KOOMEY TYPE 80 CLOSING UNIT ACCUMULATOR W/REMOTE.

ELECTRICAL UNIT: ALL UTILITY SKID MOUNTED (12' X 36') WITH LIGHTS, ELECTRIC
CONTROL PANEL AND TRANSFORMER, NEW 15 HP BACKUP AIR COMPRESSOR.
GENERATORS:
#1 WAG 220KW P/B 3306 CAT W/ELECTRIC STARTER, RADIATOR AND GUAGES.
#2 CAT SR-4 205kw B/B 3306 CAT W/ELECTRIC STARTER, RADIATOR, & GUAGES.
RIG LIGHTING.

DOGHOUSE: (2) PORCH, KNOWLEDGE BOX, LOCKERS, STORAGE AND HEATER, TOTCO 3
PEN DRILLING RECORDER, QUINCEY 350 AIR COMPRESSOR (25 HP), MOUNTED ON
TANDEM AXLE TRAILER (8' X 29')

TONGS: (2) WOOLEY TYPE B.

HOSES: ROTARY HOSE, SUCTION HOSE, VIBRATOR HOSE, 3000 PSI UPPER AND
LOWER KELLY VALVE.

HANDLING TOOLS: DRILL PIPE AND DRILL COLLAR SLIPS, SAFETY CLAMP, ASSORTED
CASING SUBS: 4 1/2", 5 1/2" 8 5/8" AND 9 5/8".

AUTOMATIC DRILLER: DICKS SATELITE.

WIRELINE UNIT: MID CONTINENT

PIPE TUB: TRAILER MOUNTED W/PIPE TRANSFER SYSTEM TO LOAD/UNLOAD
HYDRAULIC PIPE ARM, (4) SETS PIPE RACKS, (2) SHOP BUILT DRILL PIPE TUBS.

MISC: (1) LOT OF MISC. PARTS, HAND TOOLS AND SAFETY EQUIPMENT IN 8' X 30' PARTS
SHED.
TANKS: 8500 GAL. SKID MOUNTED FUEL TANK.
500 BBL WATER TANK.
500 BBL SINGLE AXLE FRAC TANK.
50 BBL BRINE TANK.

TUBULARS: 1800' USED DRILL PIPE.
(1) 6" DRILL COLLARS.
TRI-AXLE TRAILER Call (307)587-5192 for details.
706-7 Walker-Neer 250-40 1981 WORKING COMBINATION MUD AND AIR DRILLING RIG TO 6000' VERY NICE!
WALKER-NEER APACHE 250/40 TOP HEAD DRIVE DRILLING RIG

1981 WALKER-NEER Model; Apache 250/40 top head drive drilling rig, Single drum drawworks, with 10” X 42” water splashed brakes; 3 plate 24” air clutch; Hoisting capacity, 160,000# capacity. Unit complete with operators panel, and controls. Manual cathead on operator’s side; Cat-line; Pull down gauges; Top head torque gauge; Double 15” Hydromatic Brake; 30” drum clutch; Cathead;

MAST: 61’ H, with 250,000# hoisting capacity; five sheave crown block, grooved for 1” line. Hydraulically raised. 30,000 # hydraulic pull down; Chain driven. Standpipe; Rotary hose and mud line;

TOP HEAD DRIVE: KING 15PS with 30,000 # pull down capacity; Chain hoisted. All necessary hydraulic motors, fluid reservoirs, controls and gauges to make complete.

POWER: CATERPILLAR Model 3408 DI diesel engine, with ALLISON Model 5860 transmission. ( Has spare engine rebuilt by CATERPILLR, “0” hours since rebuilt)


ANCILLARY EQUIPMENT:

MARTIN-DECKER weight indicator; hydraulically operated wire line machine, complete with gauges and controls; Hydraulic service winch; Aluminum hydraulic fluid reservoir; Power washer, powered by gasoline engine;

LINCOLN, welder,

Hydraulically operated Wireline machine

Hand tools, handling tools, including slips, elevators, and subs.

ALL above mounted on tri-axle trailer, with hinged sub base; 4’ H, folding walkways with stairs and safety railings. ( Sub base rebuilt)

DOG HOUSE: 8’W X 36’L steel constructed dog house, with knowledge box; parts storage; lockers; Electric heat; BEAR automatic driller. Micro-wave oven; all above mounted on tandem axle trailer, with folding walkways, stairs and safety railings. 35 KW MARATHON LIMA generator, powered by DETRPOIT 3-53 diesel engine; Assortment of Hand tools;

BLOW OUT PREVENTOR: REGAN 8 5/8”, 3000 # annular BOP, with top and bottom , 20 hole flanges; With shop made air diverter bowl.

PIPE HANDLING: Hydraulically operated pipe racks, with Hydraulic pipe boom. Will handle pipe up to 15” in diameter.

TUBULARS:
8,416’ +/- 4” OD Grade E drill pipe, hard banded; Not inspected but appears to be yellow band quality.

(16) 6” to 6 Ό” OD drill collars, slip recessed and hard banded, with 4 “ FH connections.


MUD PUMP: CONTINENTAL EMSCO model D-375 7 Ό” X 14” duplex mud pump, S.N. 233; complete with all necessary, pluming, valving and controls to make complete; Quick change valve caps on fluid end; CONTINENTAL EMSCO pulsation dampener; OTECO relief valve; Mud gauge; Mud mixing hopper; Vibrating hose; Winch to handle hoses and lines; Powered by CATERPILLAR 3408 Diesel engine with clutch; All above unitized and skid mounted.



AIR PACKAGE:

SULLAIR model 1300 CFM @ 150 PSI air compressor, complete with all necessary piping, vales, coolers and controls to make complete; Powered by CATERPILLAR model 3406 diesel engine,, with clutch. All unitized and cabinet enclosed; Skid mounted,

SULLAIR model 1300 CFM @ 150 PSI air compressor, complete with all necessary piping, vales, coolers and controls to make complete; Powered by CATERPILLAR model 3406 diesel engine,, with clutch. All unitized and cabinet enclosed; Skid mounted,

JOY WB-12 air booster, 6” X 7” single stage, powered by CATERPILLR Model 3406 diesel engine; COTTA transmission; Complete with all necessary hoses, gauges and controls; Fabricated by WESTERN TRADING CO, in 1980. All mounted on mud boated skid, with MEYERS triplex soap pump, powered by diesel engine; soap tank; barrel racks.

275 bbl capacity water tank, with tool room and wash down pump; Skid mounted.

45’L collar trailer,

2007 PITTS 36’L drill pipe trailer tandem axle

Shop built 34’L drill pipe trailer

1979 MACK DM600 tandem axle winch tractor, S.N. DM68652796, powered by MACK diesel engine; two stick 6 speed transmission; Equipped with TULSA 64 winch with headache rack; In frame tail roller; 11R22.5 tires front and rear,


Handling tools, slips, elevators, tongs; hammer drills; hand tools; parts and accessories necessary to operate a drilling rig.
TRI-AXLE TRAILER CALL 307-587-5192 FOR PICTURES AND PRICING.
706-3 Walker-Neer 150-25 1980 COMPLETE WORKING UNIT.

DRILLING RIG: Walker-Neer Apache 150-25--50/150 mast-- King model 10PS tophead drive--Hydraulic arm drill pipe/drill collar/casing handling arm and pipe rack system--Single drum drawworks w/6 part lines p/v671 Detroit diesel engine through Allison torque converter and 5 speed transmission--Rig is mounted on (4) axle crane carrier.
SUBSTRUCTURE: 14" H x 8' W x 36' L back on sub base.
MUD PUMP: Gardner-Denver FXN 7 1/4 x 14" duplex w/Matco quick change fluid end p/b twin 671 Detroit diesel engines.
AIR COMPRESSORS: (2) 1050 cfm @ 150 psi Gardner-Denver screw type air compressors each p/b 3406 Cat diesels.
AIR BOOSTER: (1) Joy model WB-12X 7-5 p/b3406 Cat.
DOGHOUSE: 8' W x 40' L trailer mounted w/automatic driller, work bench, lockers, storage cabinets.
GENERATOR: 36KW John Deere diesel-Rig lighting.
TANKS: 300 bbl water tank, Diesel fuel tank.
WATER/SOAP INJECTION SYSTEM:
Myers triplex pump w/soap tank (skid mounted)
DRILL PIPE & COLLARS:
Approx. 4700' used 3 1/2" w/3 1/2IF tool joints.
(14) 6" drill collars.
(3) 8' x 40' pipe tubs.
Hydraulic pipe racks w/ tool tub.
BOP EQUIPMENT:
(1) 3000# annular.
(1) Washington rotating head.
HANDLING EQUIPMENT:
(2) Web Wilson Type "C" tongs.
Misc. subs and tools

Rig is mounted on (4) axle Crane Carrier chassis.
979-1 Walker-Neer CC- 2000
Con-Cor Drill w/Hydraulic pipe handling system w/loader arm--40' mast--6V71 Detroit deck engine--Air clutch on drawworks--GD WEJ air compressor 450/250 capacity--(4) hyd. Leveling jacks--King 3T top drive-- (3) axle Crane Carrier w/250 Cummins.
1169-8 Wilson Super 38 Torqair   96' x 200,000 SHL capacity w/hydraulic raising and telescoping mast w/stabbing board--Wilson 38 single drum drawworks p/b near new 350 Cat and Twin Disc torque converter--(8) part 1" line--(4) sheave x 125 ton traveling block--10'W x 10'L x 5'H substructure (rig pins to sub)--18" Oilwell rotary table-4 1/2" x 38' kelly w/roller type busing--125 ton swivel--Hydraulic leveling jacks--Weight indicator--Make up and breakout tongs--
Rig rebuilt and updated in 2006 to include new hoses, new engine plus, plus--New paint 2009
Tandem Axle Trailer
1101-2 Wilson Mogul 42   95' x 300,000 hydraulically raised and scoped mast--Single drum drawworks grooved for 1 1/8" lines w/26" (2) plate Wichita air clutch--Hydramatic brake--12V71 Detroit w/Allison 5 speed transmission--27 1/2" rotary table w/18" clutch--Sowa (4) sheave 150 ton traveling block--Weight indicator--Hydraulic breakout cylinder--6 1/2 clearance under substructure and back on ramp--No kelly, swivel or tongs included.
Rig is owned by a water well company and was used for drilling large diameter wells. It has been used very sparingly in the last few years and is stated to be in very good mechanical condition.
Three Axle Trailer
1169-10 Wilson Mogul 42 1977 1977 WILSON MOGUL 42 - Detroit 12V diesel, single drum w/double jack shaft draw-works, 102 ft. X 300,000 gross capacity hydraulically raised derrick, hyd. leveling jacks, McKissick 4 sheave block, 125 ton hook, 55 ft. swivel hose, 6 sheave crown, Martin Decker weight indicator, Parkerburg hydro-matic brakes, Foster cat heads, 1” Lebus grooved drum, stand pipe, racking board, w/cat walks & stairs, mud boat and substructure.
This rig price has been deeply discounted because the owner does not presently have any work for it. They have not operated it since they purchased it but it was drilling when they bought it. A very good buy on a portable rig with 300,000 lb. mast.
Tri-axle trailer